Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > Recovered Threads

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #31  
Old 12-27-2014, 07:57 PM
Daniel sf Daniel sf is offline
Recovered
 
Join Date: Feb 2015
Posts: 26
Default

Found some time to get back to work on the boat.I glassed a few holes at the bottom of the stringers so the foam I pour in would not leak out.Than I poured the two part foam in the stringers. My concern is that the foam i took out seemed to be much denser than the new foam I put back in. Could that be a problem?
Attached Images
  
Reply With Quote
  #32  
Old 12-27-2014, 09:01 PM
FAS FAS is offline
Recovered
 
Join Date: Dec 2015
Posts: 287
Default

nice job on the stringer foam.I would think the density would be alright as long as it is closed cell stuff...I was wondering if there was originally foam poured outward of the stringers toward the chine?Mine is an 85, and had foam between the stringers and chine, to the hull sides.I put it back that way,I guess if water can get in there,it can get out...hopefully.It seems to be sealed off pretty darn good,dont see how water could get in there, except from the stern by the rigging tubes...any thoughts?
Reply With Quote
  #33  
Old 12-28-2014, 12:14 PM
Normagain Normagain is offline
Senior Member
 
Join Date: May 2012
Location: So Cal
Posts: 163
Default

The density is also effected by temperature when you pour it. Optimum is 70 degrees for pouring. Pouring at higher temps will give you less density and fill up more volume. Probably better than pouring at lower temps where you would need a lot more liquid for the same capacity.
Reply With Quote
  #34  
Old 12-29-2014, 07:52 AM
Daniel sf Daniel sf is offline
Recovered
 
Join Date: Feb 2015
Posts: 26
Default

Mine did have foam on the sides. But I am not putting the foam back in. The temp was in the low 80s when I poured the foam.
Reply With Quote
  #35  
Old 02-01-2015, 06:46 PM
Daniel sf Daniel sf is offline
Recovered
 
Join Date: Feb 2015
Posts: 26
Default

Been working on the boat on and off but haven't been able to post. I finished the stringers with two layers of 1708. Then We glassed some marine plywood to put the gas tank on and glassed them down between the stringers. Here is the pic. What do you all think.
Attached Images
 
Reply With Quote
  #36  
Old 02-01-2015, 08:27 PM
Blue_Heron Blue_Heron is offline
Senior Member
 
Join Date: Jan 2006
Location: Gator Country
Posts: 1,416
Default

Quote:
Originally Posted by Daniel sf View Post
...What do you all think.
I think it looks very well done.
__________________
Blue Heron Boat Works
Reinventing the wheel, one spoke at a time.
Reply With Quote
  #37  
Old 02-01-2015, 08:41 PM
FLexpat FLexpat is offline
Recovered
 
Join Date: Jan 2014
Posts: 669
Default

Looks nice. You also did a good job by saving the scupper gutters with enough to tab onto.
Reply With Quote
  #38  
Old 02-01-2015, 09:44 PM
FAS FAS is offline
Recovered
 
Join Date: Dec 2015
Posts: 287
Default

lookin good on the restoration,amazing how much it takes to redo some of this stuff.you are on your way , keep us up with the picts...
Reply With Quote
  #39  
Old 02-22-2015, 09:14 AM
Daniel sf Daniel sf is offline
Recovered
 
Join Date: Feb 2015
Posts: 26
Default

I cut out part of the new deck and I glassed the bottom of it and while it was drying I started to cut out the transom. Check out the pic I wanted to do only that part of the transom but do you guys think that's a bad idea
Attached Images
 
Reply With Quote
  #40  
Old 02-22-2015, 09:16 AM
Daniel sf Daniel sf is offline
Recovered
 
Join Date: Feb 2015
Posts: 26
Default

1
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft