Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > Recovered Threads

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-14-2017, 09:53 PM
FishStretcher FishStretcher is offline
Senior Member
 
Join Date: Dec 2010
Location: Greater Boston
Posts: 1,117
Default Quick and dirty fuel tank hatch for a 20MA

My old fuel tank hatch covering the 40 gallon tank coffin was soft and very heavy from years of being reworked and lots of screws put into it. So I borrowed some tips from others here and scabbed together a melamine, MDF, and modeling clay mold.

Then I vacuum bagged a carbon, vinylester and nidacore layup. Gel coat down first. But I hurried and the gel coat hadn't cured enough so I got loads of print through. Then I forgot the breather material for the vacuum bag (doh!). So I got a dry laminate in the center under the vacuum port, so I had so re-wet the center with a wet layup and no vacuum and just peel ply.

But it came out ok in the end. Fairly light, but not nearly as light as if I was able to correctly bag it. It was 17 lb for the hatch which is about 63" x 27", plus gel coat.

I used aquarium "aragonite" as sandable anti-skid. $1 a pound at Petco, and a color match.
Attached Images
      
Reply With Quote
  #2  
Old 06-14-2017, 10:02 PM
FishStretcher FishStretcher is offline
Senior Member
 
Join Date: Dec 2010
Location: Greater Boston
Posts: 1,117
Default

A few more pictures.
Attached Images
   
Reply With Quote
  #3  
Old 06-14-2017, 11:32 PM
FishStretcher FishStretcher is offline
Senior Member
 
Join Date: Dec 2010
Location: Greater Boston
Posts: 1,117
Default

Material list:
Melamine $35 @ Home Depot
Primed 11/16" MDF trim $15@ Home Depot. Enough for two layers. The second layer is spaced out 1/8" to develop a line to trim to.
PVA
Gel coat, 1/2 gallon minimum
1.5 gallons vinyl ester resin
6 yards cloth (carbon is light, probably similar to 9-12 ounce glass??)
10mm 3/8" Nidacore (might be 7/16")
Super 77 spray adhesive to hold MDF down so there are no holes for vacuum leaks
18 feet of butyl tape
Stretchy bag
Peel ply
Don't forget breather! I heat poly pillow stuffing works.
Reply With Quote
  #4  
Old 06-15-2017, 09:23 AM
Basketcase Basketcase is offline
Senior Member
 
Join Date: Aug 2010
Location: Southern NH
Posts: 198
Default

Looks good! I need to do something similar on my aquasport but I think I can reuse the old skin and just recore it.
__________________
1971 Potter built center console.
Reply With Quote
  #5  
Old 06-15-2017, 10:26 PM
FishStretcher FishStretcher is offline
Senior Member
 
Join Date: Dec 2010
Location: Greater Boston
Posts: 1,117
Default

It might be faster that way. Unless the gel coat needs fixing. Then it might be a tie. And no grinding.
Reply With Quote
  #6  
Old 06-19-2017, 12:00 PM
Basketcase Basketcase is offline
Senior Member
 
Join Date: Aug 2010
Location: Southern NH
Posts: 198
Default

Gelcoat is good on this one. Well. As good as it's going to get. This boat is just temporary until the SeaCraft is done. So like another 5 years. lol
__________________
1971 Potter built center console.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft