1969 20' rebuild

[Old'sCool]

Following your project but if you're going with new stuff I am interested in the rod holders if you part with them.

[Captain Crabcake]

oldscool: your welcome to them ill be going new. As much as i like cool, older stuff i dont plan on going through all this to put old back on.

After being down with the kung flu for a week ive been able to get some demo done. Have her stripped down to the stringers and removed the inner skin of the transom. For the most part i left a 1 1/2" tab of the outside edge of the inner skin to attach to the new transom. Transom was like mulch, as expected. Will hopefully get new transom in within the next few weeks as long as weather temps cooperate and i can source materials. Planning on going with 1 1/2" coosa board for transom. Not sure what system i want to use, but planning the whole build for epoxy.

The stringers are pretty rough. Cracked all over the place. I am planning on raising them and wrapping with additional glass anyway so not the end of the world.

What do you guys think of height of transom cutout? ive read a few different things and it sounds like 26" is the way to go?

What do you think about how much to raise stringers? I want it to be self bailing, so i was leaning towards a minimum of 2".

Never tackled a project of this scope so any input/critisim is appreciated. Have only ever done small glassing projects and a boat load of studying on here.

[Old'sCool]

IM inbound on the rod holders. FWIW, I'm going 27" and 2-1/2".

[KNZ911]

I suggest laying a temp height sole and adjust to your preferred gunwale height. I personally like it just over my knees for stability in rougher seas. Some have gone true Conch style and have a much lower cap height.

[Captain Crabcake]

Originally Posted by KNZ911

I suggest laying a temp height sole and adjust to your preferred gunwale height. I personally like it just over my knees for stability in rougher seas. Some have gone true Conch style and have a much lower cap height.

Good thought , will do that to make sure it feels right. My goal is not to have any water in rear of the cockpit while at rest. My mako always has an inch of water, and with more than me on board it is at my feet at the helm. Drives me nuts.


Called barnegate supply today, they donÂ’t expect to have any coosa board untill April. No Penske board either. I struck out everywhere else around me as they are all wholesale. Id really like to get to glassing in the transom in the next few weeks so if anyone has any leads on some material In the south jersey area I would appreciate it. I found a place online that is 950 a sheet of 3/4 , and thatÂ’s not even with shipping. I know supply chains are having their issues, as IÂ’m dealing with it at work on pvc and ads pipet, so price is not something IÂ’m being too picky about, just want to get things moving.

[beastley]

Crab cake,
Might be a long shot but give south Jersey lumbermans a call. May have the 3/4. There off of 50 west of Egg Harbor City.
Beastley

[strick]

Originally Posted by KNZ911

I suggest laying a temp height sole and adjust to your preferred gunwale height. I personally like it just over my knees for stability in rougher seas. Some have gone true Conch style and have a much lower cap height.

This. 2" would be the max I would go...27 like olds school said is about right. Look at dirtwheel s stuff that he did...

strick

[KNZ911]

Crab,
Might want to stop by a few local shops that do restoration. They usually buy in bulk where it is beneficial to have it freight shipped to them. I know a few shops by me that I have visited, offered to sell me core and alike for their cost. A little flattery goes a long way and maybe a relationship for minor work needed!

[Captain Crabcake]

Almost have the old wood transom removed. Most of it came off with ease, except for the last 1/8 in. A 2.5 in chisel and hammer took a majority of the rest, and a disk sander is taking care of what’s bonded to the skin.



Beastley,

South jersey lumbermans came through on a sheet of 1 1/2” coosa board. Thanks for the referral. Will be hopefully getting transom done within next few weeks, then onto grinding the inside of the hull and the stringer work.

[Rbphipper]

Hi Capt, I purchased 1/2 " Penske at Barnegat last year and 3/4" Coosa at Lockwood in Sayreville three years ago. I have your twin 1972 same blue. Good luck with your build