|
|
#11
06-14-2017, 09:53 PM
|
|||
|
|||
Picking away... Coosa bulkheads. Fore to aft... integral freshwater tank +/-16 gal, 55 gal fuel tank, natural free-flowing livewell about 30 gal, and monster bilge.
 Untitled by dirtwheelsfl, on FlickrGlass pads to fasten tank to on the ends, i hate foam  Untitled by dirtwheelsfl, on FlickrFreshwater tank, will get coated before gluing/tabbing lid on  Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on FlickrAnd a lil motORvation!  Untitled by dirtwheelsfl, on Flickr
|
|
#12
06-15-2017, 07:08 AM
|
|||
|
|||
|
Nice motivation!
__________________
1975 SF18/ 2002 DF140 1972 15' MonArk/ 1972 Merc 50 http://i833.photobucket.com/albums/z...photos/SC3.jpg
|
|
#14
07-20-2017, 12:32 PM
|
|||
|
|||
|
Corecell party
 Untitled by dirtwheelsfl, on FlickrGutters lead to a not-designed-yet splashwell  Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on Flickr3" rigging tubes. (Factory stringers are off by as much as 2" side to side which made it a pain to get em "symmetrical")  Untitled by dirtwheelsfl, on FlickrFloating oil tank base. Sloped a tad to shed water...  Untitled by dirtwheelsfl, on FlickrBottom  Untitled by dirtwheelsfl, on FlickrTop. with solid glass pads to tap leaning post into  Untitled by dirtwheelsfl, on FlickrStill figuring out fuel tank... All i can say is DO NOT use "Best American Welding" in Vero Beach for anything....
|
|
#15
07-20-2017, 03:24 PM
|
|||
|
|||
|
Looks like some pretty great progress.
__________________
1971 Potter built center console.
|
|
#16
07-21-2017, 01:38 PM
|
|||
|
|||
|
You may want to consider electrical sweeps instead of the elbow 90's !
Unless you are using all fly by wire controls etc.. Just my 2¢ worth ! Nice job you are doing for sure... 
__________________
See ya, Ken ©
|
|
#17
07-21-2017, 08:32 PM
|
|||
|
|||
|
I just came across this thread. Looks like nice clean glass work and a quality build.
Dave
__________________
Blue Heron Boat Works Reinventing the wheel, one spoke at a time.
|
|
#18
07-22-2017, 08:39 PM
|
|||
|
|||
|
Thanks guys.
Pic kinda makes the elbows look squatty, theyre streets. My homie depot doesnt carry 3" gray stuff for whatever reason? Shouldnt phase teleflex extremes... not a fan of the tactile-ness ( or lack of) on the electronic stuff just yet
|
|
#19
08-25-2017, 01:19 PM
|
|||
|
|||
|
Dry fit
 Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on FlickrConsole is just a jig for the one i will build. Pretty close to the 18'er console but with a few tweaks. Mainly a bigger flat between helm panel and electronics face to fit beers! And an extension on the sides with a flat for rod holders, fuel/water fills, and a place to put feet when stting on leaning post  Untitled by dirtwheelsfl, on Flickr Untitled by dirtwheelsfl, on Flickr
|
 |
|
|
Linear Mode
