Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Repairs/Mods.
FAQ Community Calendar Today's Posts Search

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 04-01-2002, 10:48 PM
JohnB JohnB is offline
Senior Member
 
Join Date: Mar 2002
Posts: 685
Default Seacock valves on 1988 23 Scepter

I am slowly going thru and inspecting replacing wiring/plumbing/etc on my boat (have had it
2 months). The boat has 2 seacocks (1 for washdown, the other for livewell). They are pretty
crusty and I would like to replace them. Question??? Is this original seacraft equiptment,
or was is it added later? and what are the odds if I put a wrench on them they will come off
or are they likely to break/snap off? Thanks John
__________________
http://www.deep-blue-sea.org/seacraf...aftTarpon2.jpg
JohnB / 23' SeaCraft
Reply With Quote
  #2  
Old 04-02-2002, 01:23 AM
Scott Scott is offline
Senior Member
 
Join Date: Feb 2002
Posts: 1,272
Default Re: Seacock valves on 1988 23 Scepter

John
Cant speak to the original equipment question...but as to your other question I would definitely replace as I did just what you said and snapped a badly corroded, poorly installed thru hull off down at the pick up. I tried tapping it to break up the corrosion, penetrating oils, heat... well you get the idea...then I just put a little muscle [img]images/icons/grin.gif[/img] into it and POW....This better not have been a factory install ... as it was very poorly done. I would even consider getting rid of one of those thru hulls and feeding both from one...My personal opinion is the less holes in the bottom the better...I've seen one too many boat on the bottom in its slip because of below the water line failure of plumbing...Including a relatively new (three year old) Davis boat.....Talk about an ouch!!

Scott
Reply With Quote
  #3  
Old 04-02-2002, 10:10 AM
Miles Offshore Miles Offshore is offline
Senior Member
 
Join Date: Feb 2002
Location: Virginia Beach, Virginia
Posts: 1,260
Default Re: Seacock valves on 1988 23 Scepter

I agree with Scott replace them!!!!!
__________________
"Lifes too short to own an ugly boat"
Reply With Quote
  #4  
Old 04-02-2002, 02:32 PM
FELLOW-SHIP FELLOW-SHIP is offline
Senior Member
 
Join Date: Feb 2002
Location: Cooper City, Fl
Posts: 1,798
Default Re: Seacock valves on 1988 23 Scepter

I HAVE A 1976 23' OPEN FISH I REPLACED ALL THE THROUGH HULL FITTINGS. THEY WERE STARTING TO SHOW THEIR AGE I DIDN'T WANT TO DO 95% OF THE JOB AND THEN HAVE A MAJOR PROBLEM BECAUSE I DECIDED TO SKIP SOME CORNERS.
FELLOW-SHIP [img]images/icons/wink.gif[/img]
Reply With Quote
  #5  
Old 04-02-2002, 08:44 PM
JohnB JohnB is offline
Senior Member
 
Join Date: Mar 2002
Posts: 685
Default Re: Seacock valves on 1988 23 Scepter

All,
Thanks for the input, I replaced both seacocks today. The fittings thru the hull were heavy brass and looked ok to me. I also replace all the hoses and clamps, a bunch of wire, double checked everything and closed it up. I was suprised how clean the bilge and bottom areas of the boat where. I did the same thing on my center console, and it was a mess..... At least now I can reach thru the access plate and open and close the seacocks.
__________________
http://www.deep-blue-sea.org/seacraf...aftTarpon2.jpg
JohnB / 23' SeaCraft
Reply With Quote
  #6  
Old 04-02-2002, 11:48 PM
Miles Offshore Miles Offshore is offline
Senior Member
 
Join Date: Feb 2002
Location: Virginia Beach, Virginia
Posts: 1,260
Default Re: Seacock valves on 1988 23 Scepter

John, now you will have "peace of mind "as well!!!
craig
__________________
"Lifes too short to own an ugly boat"
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft